The BIS recommends that the size of a door frame and window frame should be derived after allowing a margin of______ mm alround an opening for convenience of fixing.(a) 2 mm(b) 6 mm(c) 5 mm(d) 10 mmI got this question during a job interview.My doubt stems from Components of a Door topic in division Doors, Windows and Ventilators of Construction & Building Materials

The BIS recommends that the size of a door frame and window frame shou

1.	The BIS recommends that the size of a door frame and window frame should be derived after allowing a margin of______ mm alround an opening for convenience of fixing.(a) 2 mm(b) 6 mm(c) 5 mm(d) 10 mmI got this question during a job interview.My doubt stems from Components of a Door topic in division Doors, Windows and Ventilators of Construction & Building Materials
Answer» Correct CHOICE is (d) 10 mm Easiest explanation: The width and height of an opening is INDICATED by NUMBER of MODULES where each module is of 100 mm. The height of opening for door is considered from below the floor finish to the bottom of lintel.

Discussion

No Comment Found

Related InterviewSolutions

In the designation 6 WS 12, the letter S stands for __________(a) Window opening(b) Single shutter(c) Double shutter(d) Height of opening
A door should not be located in the centre of a wall.(a) True(b) FalseI had been asked this question during an interview.This question is from Location of Doors and Windows in chapter Doors, Windows and Ventilators of Construction & Building Materials
A ____________ may be defined as an opening made in a wall for the purpose of providing daylight, vision and ventilation.(a) Ventilator(b) Door(c) Shutter(d) WindowI had been asked this question in an international level competition.My query is from Components of a Door topic in chapter Doors, Windows and Ventilators of Construction & Building Materials
Which type of handle is represented in the given figure?(a) Bow type(b) Lever handle(c) Wardrobe handle(d) Door handleI have been asked this question in examination.Asked question is from Doors, Windows and Ventilators topic in chapter Doors, Windows and Ventilators of Construction & Building Materials
_________ windows are provided near the top of main roof.(a) Lanterns(b) Skylight(c) Clerestorey(d) BayThe question was posed to me during an online interview.The above asked question is from Types of Windows in section Doors, Windows and Ventilators of Construction & Building Materials
Which of the following is not a type of joint between the head and the post of the timber frame?(a) Closed mortised and tenoned joint(b) Open and pin joint(c) Pin and tenoned joint(d) Dovetailed jointI have been asked this question during an interview.My question is taken from Door Frames topic in portion Doors, Windows and Ventilators of Construction & Building Materials
__________ is the openable part of a door or window.(a) Frame(b) Rail(c) Shutter(d) SillThis question was addressed to me in an international level competition.The doubt is from Definition of Technical Terms topic in division Doors, Windows and Ventilators of Construction & Building Materials
Which of the following bolts is used to secure high doors?(a) Aldrop(b) Latch(c) Espagnolette bolt(d) Flush boltI got this question in quiz.My question is from Doors, Windows and Ventilators topic in chapter Doors, Windows and Ventilators of Construction & Building Materials
__________ windows are provided at the corner of a room.(a) Circular(b) Corner(c) Gable(d) DormerThe question was asked by my school principal while I was bunking the class.My enquiry is from Types of Windows in portion Doors, Windows and Ventilators of Construction & Building Materials
The size of ________ depends on the dimension of the room, use of the room, location of the room, direction and speed of the wind, obstruction to light by neighbouring buildings, etc.(a) Ventilator(b) Door(c) Window(d) LintelsI have been asked this question during an interview.My question is based upon Components of a Door topic in chapter Doors, Windows and Ventilators of Construction & Building Materials

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment