____________ is used to measure the flow velocity across a cross-section with a known area.(a) Inferential meter(b) Anemometer(c) Speedometer(d) BarometerThis question was addressed to me by my college director while I was bunking the class.My enquiry is from Plumbing for Buildings in portion Plumbing for Buildings of Construction & Building Materials

____________ is used to measure the flow velocity across a cross-secti

1.	____________ is used to measure the flow velocity across a cross-section with a known area.(a) Inferential meter(b) Anemometer(c) Speedometer(d) BarometerThis question was addressed to me by my college director while I was bunking the class.My enquiry is from Plumbing for Buildings in portion Plumbing for Buildings of Construction & Building Materials
Answer» The CORRECT choice is (a) INFERENTIAL meter The BEST I can explain: There are generally two types of meters USED in water distribution systems. These are inferential meter and displacement meter. The inferential meter is used to MEASURE the flow velocity across a cross-section with a known area.

Discussion

No Comment Found

Related InterviewSolutions

In the two-pipe system for the drainage of buildings, the discharge from the waste pipe is disconnected from the drain by using __________(a) Gully trap(b) Silt trap(c) Floor trap(d) Grease trapThe question was asked in an interview.My question is taken from Systems of Plumbing in chapter Plumbing for Buildings of Construction & Building Materials
The depth of a sludge soak pit varies from _____________(a) 0.5-1.75 m(b) 2.5-4 m(c) 5-6.5 m(d) 8-9.5 mThis question was addressed to me during a job interview.This interesting question is from Systems of Plumbing in chapter Plumbing for Buildings of Construction & Building Materials
The diameter of a sludge soak pit varies from __________(a) 0.5-1 m(b) 1-1.5 m(c) 2-3 m(d) 5-6 mThis question was posed to me during an online exam.I want to ask this question from Systems of Plumbing in section Plumbing for Buildings of Construction & Building Materials
One pipe system is cheaper than the single stack system for the drainage of buildings.(a) True(b) FalseThe question was posed to me in class test.My question is taken from Systems of Plumbing topic in portion Plumbing for Buildings of Construction & Building Materials
Which of the following statements regarding systems of plumbing for drainage of buildings is not correct?(a) Only one pipe is used in the single stack system(b) A separate vent pipe is provided in one pipe system(c) The traps of basins are directly connected to the vent pipe in the partially ventilated single stack system(d) The full form of S.W.P. is soil and waste pipeI have been asked this question in a national level competition.My doubt stems from Systems of Plumbing topic in chapter Plumbing for Buildings of Construction & Building Materials
Septic action is produced by the septic tank by __________(a) Fungi(b) Virus(c) Termites(d) Anaerobic bacteriaI have been asked this question during an online interview.Origin of the question is Systems of Plumbing topic in portion Plumbing for Buildings of Construction & Building Materials
The outlet pipe in the septic tank is kept about _________ lower than the inlet pipe.(a) 5 cm(b) 10 cm(c) 15 cm(d) 30 cmThe question was asked at a job interview.I want to ask this question from Systems of Plumbing in chapter Plumbing for Buildings of Construction & Building Materials
In the two-pipe system for the drainage of buildings, the discharge from the water closet is connected to the waste pipe while the discharge from the sinks and baths is connected to the soil pipe.(a) True(b) FalseThis question was addressed to me at a job interview.This interesting question is from Systems of Plumbing topic in chapter Plumbing for Buildings of Construction & Building Materials
The size of the vent pipe commonly used in house drainage is ________(a) 30 mm(b) 100 mm(c) 50 mm(d) 75 mmI had been asked this question in an interview for job.I need to ask this question from Plumbing for Buildings topic in division Plumbing for Buildings of Construction & Building Materials
Which of the following is not a classification of traps based on their shape?(a) P-trap(b) Q-trap(c) S-trap(d) W-trapThis question was posed to me in homework.Enquiry is from Plumbing for Buildings topic in division Plumbing for Buildings of Construction & Building Materials

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment