For retaining compression in the cylinder, a flat piece of ___________ is placed between the cylinder head and cylinder block.(a) gasket(b) rims(c) cylinder liner(d) invar strutI had been asked this question during an online interview.I would like to ask this question from Cylinder Head topic in division Engine Construction & Wheel Assembly of Automobile Engineering

For retaining compression in the cylinder, a flat piece of ___________

1.	For retaining compression in the cylinder, a flat piece of ___________ is placed between the cylinder head and cylinder block.(a) gasket(b) rims(c) cylinder liner(d) invar strutI had been asked this question during an online interview.I would like to ask this question from Cylinder Head topic in division Engine Construction & Wheel Assembly of Automobile Engineering
Answer» Right choice is (a) gasket The EXPLANATION is: Gaskets are coated with SPECIAL varnish which melts and seals all the SMALL inter sticks of the block and head when the engines warms up. The gaskets besides WITHSTANDING high PRESSURE should also withstand high temperature also.

Discussion

No Comment Found

Related InterviewSolutions

What does the code 145 SR -13 tire designation represent?(a) 145” width, 13” diameter, cross-ply(b) 145 mm width, 13” diameter, radial-ply(c) 145” width, 13 cm diameter, radial-ply(d) 145 mm width, 13 cm diameter, cross-plyI have been asked this question in a job interview.I want to ask this question from Wheel and Tire topic in section Engine Construction & Wheel Assembly of Automobile Engineering
What is the purpose of tire rotation on automobiles?(a) Avoid ply separation(b) Equalize wear(c) Get better ride(d) Reduce bumpI got this question in an interview for internship.This intriguing question comes from Wheel and Tire topic in portion Engine Construction & Wheel Assembly of Automobile Engineering
What do the permissible of mixing cross-ply and radial-ply automobile tires allow?(a) Cross-ply tires on left wheels(b) Cross-ply tires on right wheels(c) Cross-ply tires on front wheels(d) Cross-ply tires on rear wheelsThis question was posed to me in unit test.Origin of the question is Wheel and Tire in division Engine Construction & Wheel Assembly of Automobile Engineering
Where will an overinflated tire wear the thread most?(a) Near center(b) Near the edge(c) In the cross direction(d) In the lateral directionI have been asked this question in semester exam.The doubt is from Wheel and Tire topic in section Engine Construction & Wheel Assembly of Automobile Engineering
Where will an underinflated tire wear the thread most?(a) Near center(b) Near the edge(c) In the cross direction(d) In the lateral directionI had been asked this question in an online interview.Asked question is from Wheel and Tire topic in section Engine Construction & Wheel Assembly of Automobile Engineering
What does the ‘ply rating’ refer to?(a) Aspect ratio(b) Rated strength(c) Recommended inflation pressure(d) The actual number of pliesI had been asked this question in an interview for job.My question is based upon Wheel and Tire in division Engine Construction & Wheel Assembly of Automobile Engineering
In case of a wire wheel, the vehicle weight is supported by the wire in _________(a) Tension(b) Bending(c) Shear(d) CompressionI got this question in an interview for internship.I'm obligated to ask this question of Wheel and Tire in portion Engine Construction & Wheel Assembly of Automobile Engineering
The cylinder block and upper half of the crank case are cast by _________ material.(a) aluminium(b) zinc(c) semi-steel(d) titaniumI got this question in final exam.Enquiry is from Cylinder Head topic in portion Engine Construction & Wheel Assembly of Automobile Engineering
_________ serves as a cooling and ventilation of engine lubricating oil.(a) crank case(b) oil sump(c) cam shaft(d) pistonThe question was asked in a national level competition.My question is from Cylinder Head topic in division Engine Construction & Wheel Assembly of Automobile Engineering
____________ is combination of fibre and cork granules that is more compressible and resilient.(a) karropak(b) felicoid(c) shimbestos(d) metal sandwichI have been asked this question during an online exam.Question is taken from Cylinder Head topic in division Engine Construction & Wheel Assembly of Automobile Engineering

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment