Volt-sec balance method is based on the principle of the energy of conservation.(a) True(b) FalseThe question was posed to me during a job interview.My enquiry is from Solid-State Switching Circuits in chapter Introduction to Solid-State Switching Circuits of Electric Drives

Volt-sec balance method is based on the principle of the energy of con

1.	Volt-sec balance method is based on the principle of the energy of conservation.(a) True(b) FalseThe question was posed to me during a job interview.My enquiry is from Solid-State Switching Circuits in chapter Introduction to Solid-State Switching Circuits of Electric Drives
Answer» The CORRECT ANSWER is (a) True To explain I would say: Volt-sec balance method states that the net AREA over the cycle will be zero. It is based on the principle of the energy of conservation. The amount of CHARGING is equal to DISCHARGING.

Discussion

No Comment Found

Related InterviewSolutions

Forced commutated CSI require _________(a) Diode(b) Resistor(c) Inductor(d) CapacitorI had been asked this question in an interview.Origin of the question is Solid-State Switching Circuits in division Introduction to Solid-State Switching Circuits of Electric Drives
1600 V rated 8 SCRs are connected in series. The operation voltage of the string is 4400. Calculate the string efficiency.(a) 34.37 %(b) 30.15 %(c) 38.48 %(d) 35.84 %I have been asked this question in an interview.I'd like to ask this question from Solid-State Switching Circuits in portion Introduction to Solid-State Switching Circuits of Electric Drives
Calculate the average value of thyristor current in 3-Φ Full wave converter for the load current=729 A and α=3°.(a) 254 A(b) 285 A(c) 247 A(d) 243 AThis question was posed to me in unit test.Origin of the question is Solid-State Switching Circuits in chapter Introduction to Solid-State Switching Circuits of Electric Drives
Full form of FET is ___________(a) Field effect transistor(b) Field engage transistor(c) Field effect terminal(d) Fire engage transistorThe question was asked by my school principal while I was bunking the class.Enquiry is from Solid-State Switching Circuits topic in portion Introduction to Solid-State Switching Circuits of Electric Drives
TRIAC is a unipolar switch.(a) True(b) FalseI have been asked this question at a job interview.My doubt stems from Solid-State Switching Circuits topic in chapter Introduction to Solid-State Switching Circuits of Electric Drives
Full form of SCR is ____________(a) Silicon controlled rectifier(b) State-controlled rectifier(c) State cover rectifier(d) State-controlled resetThis question was addressed to me in an international level competition.Question is taken from Solid-State Switching Circuits topic in division Introduction to Solid-State Switching Circuits of Electric Drives
Calculate the form factor if V(r.m.s)=45 V, V(avg)=15 V.(a) 2(b) 5(c) 3(d) 8The question was asked during an online interview.This intriguing question originated from Solid-State Switching Circuits in division Introduction to Solid-State Switching Circuits of Electric Drives
Calculate the circuit turn-off time for 3-Φ Fully controlled rectifier if the firing angle is 13° and supply frequency is 49.5 Hz.(a) 730.2 msec(b) 740.8 msec(c) 754.5 msec(d) 755.1 msecThis question was addressed to me in my homework.I want to ask this question from Solid-State Switching Circuits in chapter Introduction to Solid-State Switching Circuits of Electric Drives
Calculate the value of the Input power factor for 3-Φ Fully controlled rectifier if the firing angle value is 16°.(a) .96(b) .91(c) .93(d) .94The question was posed to me by my college professor while I was bunking the class.This key question is from Solid-State Switching Circuits in section Introduction to Solid-State Switching Circuits of Electric Drives
Calculate the value of the Input power factor for 1-Φ Full wave bridge rectifier if the firing angle value is 39°.(a) .69(b) .59(c) .78(d) .15This question was posed to me in quiz.The question is from Solid-State Switching Circuits in section Introduction to Solid-State Switching Circuits of Electric Drives

Volt-sec balance method is based on the principle of the energy of conservation.(a) True(b) FalseThe question was posed to me during a job interview.My enquiry is from Solid-State Switching Circuits in chapter Introduction to Solid-State Switching Circuits of Electric Drives

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment