The emf of a storage battery is `90 V` before charging and `100 V` after charging. When charging began the current was `10 A`. What is the current at the end of charging if the internal resistance of the storge battery during the whole process of charging may be taken as constant and equal to `2Omega`?

The emf of a storage battery is `90 V` before charging and `100 V` aft

1.	The emf of a storage battery is `90 V` before charging and `100 V` after charging. When charging began the current was `10 A`. What is the current at the end of charging if the internal resistance of the storge battery during the whole process of charging may be taken as constant and equal to `2Omega`?
Answer» The voltage supplied by the charging plant is here constant which is equal to `V=E_i+i_i.r=(90)+(10)(2)` `=10V` ltbergt Let `i_f` be the current at the end of charging Then, `V=E-f+i_fr` `i_f=(V-E_f)/r` `=(110-100)/2` `=5A`

Discussion

No Comment Found

Related InterviewSolutions

The effective between A&B in the given circuit isA. `7Omega`B. `2Omega`C. `6Omega`D. `5Omega`
A source of e.m.f. `E = 15V` and having negligible internal resistance is connected to a variable resistance so that the current in the circuit increases with time as `i = 1.2 t +3` Then, the total charge that will flow in first five second will beA. `10C`B. `20C`C. `30C`D. `40C`
Two cells of emfs approximately 5V and 10V are to be accurately compared using a poteniometer of length 400 cm.A. The battery that runs the potentiometer should have voltage of 8 VB. The battery of potentiometer can have a voltage of 15 V and R adjusted so that the potential drop across the wire slightly exceeds 10 VC. The first portion of 50 cm of wire itself should have a potential drop of 10 VD. Potentiometer is usually used for comparing resistance and not voltages
Two cells of emfs approximately 5V and 10V are to be accurately compared using a poteniometer of length 400 cm.A. The battery that runs the potentionmeter should have voltage of 8 VB. The battery of potentionmeter can have a voltage of 15V and R adjusted so that the potential drop across the wire slightly exceeds 10 VC. The first portion of 50cm of wire itself should have a potential drop of 10VD. Potentiometer is usually used for comparing resistances and not voltages
Two cells of e.m.f. 10V & 15V are connected in parallel to each other between points A&B. The cell of e.m.f. 10V is ideal but the cell of e.m.f. 15V has internal resistance `1Omega`. The equivalent e.m.f. between A and B is: A. `25/2V`B. not definedC. 15 VD. 10 V
Two cells of emfs approximately 5V and 10V are to be accurately compared using a poteniometer of length 400 cm.A. Toe battery that runs the potentiometer should have voltage of 8 V.B. Toe battery of potentiometer can have a voltage of 15 V and R adjusted so that the potential drop across the wire slightly exceeds 10 V.C. The first portion of 50 cm of wire itself should have a potential drop of 10 VD. Potentiometer is usually used for comparing resistances and not voltages.
In the `R_(1) = 10 Omega ,R_(2) = 20 Omega, R_(3) = 40 Omega R_(4) = 80 Omega` and `V_(A) = 5V,V_(B) = 10V,V_(c) = 20V,V_(D) = 15V` The current in the resistance `R_(1)` will be A. `0.4 A` toward OB. `0.4A` away from OC. `0.8A` toward OD. `0.8A` toward O
The amount of charge Q passed in time t through a cross-section of a wire is `Q=5t^(2)+3t+1`. The value of current at time t=5 s isA. 9AB. 49AC. 53AD. None of these
The charge flowing through a conductor varies with time as `q= 8 t - 3t^(2)+ 5t^(3)` Find (i) the initial current (ii) time after which the current reaches a maximum value of current
The current in a conductor varies with time `t` as `I=3t+4t^(2)` Where I in amp and t in sec. The electric charge flows through the section of the conductor between `t=1s` and `t=3s`A. `(100)/(3)C`B. `(127)/(4)C`C. `(140)/(3)C`D. `(150)/(3)C`

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment