Narrowing the range of required dimensions make the casting more expensive and difficult to produce.(a) True(b) FalseThis question was posed to me in my homework.My enquiry is from Dimensional Inspection topic in section Inspection Testing in Foundries of Casting-Forming-Welding I

Narrowing the range of required dimensions make the casting more expen

1.	Narrowing the range of required dimensions make the casting more expensive and difficult to produce.(a) True(b) FalseThis question was posed to me in my homework.My enquiry is from Dimensional Inspection topic in section Inspection Testing in Foundries of Casting-Forming-Welding I
Answer» The correct option is (a) True For explanation I WOULD say: The range between the lower tolerance limit and UPPER tolerance limit is always set by a producer to make dimensions to come within the range, but the narrowing or shortening of range makes the casting more expensive and DIFFICULT to PRODUCE, and problems also arise while testing of casting.

Discussion

No Comment Found

Related InterviewSolutions

In impact testing of materials, the notches are made to reduce the stress concentration.(a) True(b) FalseThis question was addressed to me in an internship interview.Query is from Destructive Testing in division Inspection Testing in Foundries of Casting-Forming-Welding I
Which of the following methods of inspection uses high frequency of sound waves for the detection of flaws in the castings?(a) Penetrant test(b) Radiography(c) Pressure test(d) Ultrasonic inspectionThe question was posed to me in a national level competition.Question is from Non Destructive Testing in chapter Inspection Testing in Foundries of Casting-Forming-Welding I
In non-destructive testing, sound test used is a very fine and accurate method of detecting flaws in the castings.(a) True(b) FalseThe question was posed to me in semester exam.My doubt stems from Non Destructive Testing topic in division Inspection Testing in Foundries of Casting-Forming-Welding I
Destructive tests are generally much easier to interpret than the non-destructive tests.(a) True(b) FalseThe question was asked in an interview for internship.This interesting question is from Destructive Testing topic in section Inspection Testing in Foundries of Casting-Forming-Welding I
Which subject classification of the MFFT has the characteristics, short time spending and high errors making?(a) Fast-accurates(b) Slow-inaccurates(c) Reflectives(d) ImpulsivesThis question was posed to me in unit test.I need to ask this question from Visual Inspection topic in section Inspection Testing in Foundries of Casting-Forming-Welding I
Inspection of castings is mainly carried out to detect any flaws in the castings.(a) True(b) FalseThis question was addressed to me in homework.Question is from Inspection and Testing topic in portion Inspection Testing in Foundries of Casting-Forming-Welding I
Negative surface irregularities cannot be caused by which of the following factor?(a) Slag inclusion(b) Oxidation pitting(c) Nitride pitting(d) ShrinkageThe question was posed to me during an online interview.Question is from Visual Inspection in chapter Inspection Testing in Foundries of Casting-Forming-Welding I
Computerization in dimensional inspection improves the speed and accuracy of measuring casting dimensions.(a) True(b) FalseI had been asked this question during an online interview.My question is taken from Dimensional Inspection topic in portion Inspection Testing in Foundries of Casting-Forming-Welding I
In ultrasonic inspection, there is no chance of rejection of good material.(a) True(b) FalseThe question was asked by my college director while I was bunking the class.I would like to ask this question from Inspection Procedures topic in portion Inspection Testing in Foundries of Casting-Forming-Welding I
Magnetic particle inspection is a very sensitive technique for the detection of defects in the castings.(a) True(b) FalseI had been asked this question in a national level competition.Question is taken from Inspection Procedures in chapter Inspection Testing in Foundries of Casting-Forming-Welding I

Narrowing the range of required dimensions make the casting more expensive and difficult to produce.(a) True(b) FalseThis question was posed to me in my homework.My enquiry is from Dimensional Inspection topic in section Inspection Testing in Foundries of Casting-Forming-Welding I

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment