Addition of surface to water leads .A. An increase in angle of contactB. An increase in surface tensionC. A decrease in angle of contact and increase in surface tension .D. A decrease in angle of contact and increase in surface tension .

Addition of surface to water leads .A. An increase in angle of contact

1.	Addition of surface to water leads .A. An increase in angle of contactB. An increase in surface tensionC. A decrease in angle of contact and increase in surface tension .D. A decrease in angle of contact and increase in surface tension .
Answer» Addition of soap redues surface tension of system.

Discussion

No Comment Found

Related InterviewSolutions

When is deviation more in the behaviour of a gas from the ideal gas equation `PV=nRT`?A. At high temperature and low pressureB. At low temperature and high pressureC. At high temperature and high pressureD. At low temperature and low pressure
The density of a gas filled in electric lamp is `0.75kg//m^(3)` . After the lamp has been switched on, the pressure in it increases from `4xx10^(4)` Pa to `9xx10^(4)` Pa. What is increases in `u_("rms")` ?A. 100B. 200C. 300D. None of these
In a glass tube columns of water and mercury appear as shown. This is best attributed to the differences in their:A. densitiesB. molar massesC. surface tensionsD. viscosities
The volume of real gases often exceed those calculated by the ideal gas equation. These deviations are best attributed to the:A. attractive forces between the molecuels in real gases.B. dissociation of the molecuels in real gases.C. kinatic energy of the molecules in real gases.D. volumes of the molecules in rel gases.
A container holds 3 liter of `N_(2(g))` and `H_(2)O_((l))` at `29^(@)C` The prssure is found to be 1 atm The water in container is instantaneously electrolysed to give `H_(2)` and `O_(2)` following the reaction `H_(2)O_(l) rarrH_(2(g)) +(1)/(2)O_(2_(g))` At the end of electrolysis the pressure was found to be `1.86atm` calculate the amount of water present in the container If the aqueous tension of water at `29^(@)C` is `0.04 atm ` .
Match of following (where `U_(rms)`=root mean square speed `U_(av)` =average speed `U_(mp)` = most probable speed) `{:(,"List-I",,"List-II"),("(a)",U_(rms)//U_(av),,(p)1.22),("(b)",U_(av)//U_(mp),,"(q)1.13"),((c),U_(rms)//U_(mp),,"(r)1.08):}`
The `u_(rms)` of a gas at `300K` is `3R^(1//2)` The molar mass of the gas in `kg mo1^(-1)` is .A. `1.0 xx 10^(-1)`B. `1.0 xx 10^(-2)`C. `1.0 xx 10^(-3)`D. `1.0`
The cirtical constant for water are `374^(@)C` 218 atm and 0.0566 liter `mo1^(-1)` Calculate a,b and `R` .
The density of a gas `A` is twice that of a gas `B` at the same temperature. The molecular mass of gas `B` is thrice that of `A`. The ratio of the pressure acting on `A` and `B` will beA. `6:1`B. `7:6`C. `2:5`D. `1:4`
`n_(1)` and `n_(2)` moles of two ideal gases (mo1 wt `m_(1)` and `m_(2))` respectively at temperature `T_(1)K` and `T_(2)K` are mixed Assuming that no loss of energy the temperature of mixture becomes .A. `n_(1)T_(1)+n_(2)T_(2)`B. `(n_(1)T_(1)+n_(2)T_(2))/(T_(1)+T_(2))`C. `(n_(2)T_(1)+n_(1)T_(2))/(n_(1)+n_(2))`D. `(T_(1)xxT_(2))/(n_(1)xxn_(2))`

Addition of surface to water leads .A. An increase in angle of contactB. An increase in surface tensionC. A decrease in angle of contact and increase in surface tension .D. A decrease in angle of contact and increase in surface tension .

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment